Built 11/99

Editor's Note: This be t' actual buildin' experience from the Scratch Magnetic Apogee Detection Sensor.

One o' t' key benefits t' bein' an NARRRRR member is that you get a subscription t' Sport Rocketry. Lots o' issues are filled with vaguely interestin' articles, shiver me timbers, me bucko, rocket related o' course, arrr, shiver me timbers, but t' one thin' that caught my eye immediately be t' Magnetic Apogee Sensor! Written by Robert Galejs, the article went into detail on his development o' a concept into a working device! This be really fascinating. Ya scallywag! I read and reread t' article several times, arrr, shiver me timbers, and even contemplated tryin' t' wire up me own. Schematics and even a board pattern was included. Well, blow me down! Unfortunately, me bucko, I studied mechanical engineering, and electrical things are still somewhat intimidating. Aye aye! I considered tryin' to put one together for about 4, maybe 5 seconds. Arrr! Ahoy!

How does it work? We're all familiar with t' magnetic poles o' t' earth and t' idea o' havin' a compass tell you which way is magnetic North. Ahoy! However, as it turns out, matey, me hearties, thar's a significant vertical component t' t' magnetic field, which means that, at least in certain parts o' t' world, you can also have a "compass" tell you which way is magnetic "up."

KEWL!

Fast forward t' a few weeks later. Well, blow me down! It's late at night and I'm pokin' through RMR when I see a postin' by none other than Robert Galejs himself! Blimey! It turns out that in t' months that it takes an article t' work it's way into Sprocketry, he had been off workin' t' bugs out o' t' magnetic apogee sensor, matey, and even had assembled a few kits for construction! Blimey! Sweet! Blimey!

I read his postin' more carefully and hesitate. Ya scallywag! SMT? That's Surface mount, isn't it? Bummer. For those o' you who are unfamiliar, me hearties, ya bilge rat, these are t' dust particle sized electronic components that allow you t' make walkmans t' size of cigarette packs and telephones t' size o' matchboxes. Blimey! I'm pretty handy with an exacto, but a solderin' iron? Forget it.

After tradin' a couple o' e-mails, me hearties, me hearties, I decide t' try it anyway. Arrr! How bad can it be? I also make a mental note t' stop by rat shack for a fine point soldering iron. Well, blow me down! $25 and a week later, I am openin' a padded manila mailer from Massachusetts. Another late night, this time solderin' teeny tiny components onto a circuit board which is a little larger than a cigarette. Begad! Tweezers, micro-clips, me hearties, and lots o' patience.

I hold t' components down with micro-clips, arrr, me hearties, then lightly touch the solderin' iron t' t' joint. Blimey! Begad! This isn't as bad as I thought it was!!! There's lots o' stuff t' put on and it's lookin' pretty good!

Crack! Damn. Ya scallywag! I just broke one o' t' capacitors. Avast! I tried t' use hemostats to hold t' component in place as I solder it. Begad! I should have stayed with t' micro clips. Aye aye! Lookin' over t' schematic and t' magazine article carefully, arrr, I figure out that t' value o' this particular cap isn't important. Avast, me proud beauty! Well, shiver me timbers, blow me down! I fish out a tiny capacitor from me junk box and solder it in place. Avast!

Done. Begad! Hook up t' battery. Avast, me proud beauty! Blink. Begad!

It doesn't work. Arrr!

What did I do?

I look at t' components and double check t' instructions. Blimey! Arrr!

After much inspection and fiddling, matey, me bucko, I decide t' send a note t' Rob and go to bed. Ahoy! Avast! I get a response t' next day, and before I have a chance t' do the diagnostics he recommends, arrr, me bucko, I decide t' check t' solder joints again. Aye aye! Blimey! This time I use an exacto knife. Blimey! Bingo! It turns out that 3 joints are nay complete. I solder them and it works!

I have since purchased another kit and assembled it. Blimey! Both sensors have been calibrated and tested, me hearties, though I haven't had t' chance t' actually fly them. Ya scallywag! Avast! I have modifies one with a mini-jack so it holds t' flashbulb circuit open (for safety) when it is inserted - and at t' same time puts a test LED across the circuit.

I HIGHLY recommend this kit. Ahoy! Get them while they last! T' finished sensor is small enough t' fit in BT5!! This opens up a huge realm o' model rocket design. Begad! I have lots o' sketches already for FAR OUT rockets. Ahoy! Just you wait!

Here are me tips:

1) Get a solderin' iron, 15-20 watts, with t' smallest tip you can find. Ahoy! Avast, me hearties, me proud beauty!

2) Get some tweezers and a magnifyin' glass. Arrr! Blimey! Begad! Blimey! These things are tiny. Avast, me proud beauty! Blimey! Work on a large clean table where you can find items easily if dropped. Avast! Blimey! Arrr! Blimey! If you have a room with a hard floor, shiver me timbers, it will be easier t' find anythin' if you drop it.

3) Use tape, glue, micro clips, me hearties, matey, etc. Ahoy! t' hold t' components in place while you're soldering. Be very careful about applyin' too much pressure as some of them are brittle. Begad! Avast, me proud beauty! Blimey!

4) Test all your solder joints t' make sure they are tacked down properly. Avast, me proud beauty! Avast!

5) Be patient!