Brief:
This is a free, easy, 13mm, matey, arrr, paper shroud saucer which uses an aerobrake recovery. Aye aye! T' 13mm Cinco is a diminutive version o' Art Applewhite's Cinco saucer. Aye aye! It is nay a kit, per se; it is offered as a free download in t' form o' a PDF file on his web site.

Construction:
This rocket is made from a single sheet o' Card stock. Aye aye! You download t' PDF, put a piece o' card stock in t' printer and print it out. Other than that, matey, you will need some white glue, a straightedge and a razor knife.

Construction begins by cuttin' out t' motor mount. Ahoy! A razor knife is used t' carefully cut around t' solid lines. Somethin' a bit less sharp should be used in conjunction with a straightedge t' score t' dashed lines for easy folding. Ya scallywag! After t' mount is cut out, t' top tabs o' t' mount are folded down and glued t' t' next tab down. Avast, me proud beauty! The middle tabs are then folded and glued t' t' interior o' t' motor mount. When t' mount is folded into a tube, me hearties, me hearties, these tabs form t' thrust ring. Ahoy! Begad! T' motor tube assembly is set aside t' dry while t' shroud is formed.

T' shroud is also cut out. Again, cuts are made along t' solid lines and folds are scored along t' dashed lines. Well, blow me down! Avast! A hole is cut for t' motor mount and a notch is cut out for t' launch rod. T' upper part o' t' shroud is then folded into shape and a tab is used t' glue it. Well, arrr, blow me down! After that, shiver me timbers, ya bilge rat, t' lower shroud is folded and then inverted into the upper shroud. Avast, me proud beauty! T' two shrouds are held together with white glue.

After t' shroud has a chance t' dry, t' motor tube is inserted into t' cavity cut for that purpose. Blimey! Blimey! Blimey! Blimey! Care needs to be taken so that t' thrust rin' is at t' top o' t' rocket. Aye aye! Blimey! It should protrude about 1/32" above t' top. Well, blow me down! Blimey! Avast, matey, me proud beauty! Blimey! A fillet o' white glue is used t' fasten t' motor mount t' t' shroud, ya bilge rat, top and bottom. Ya scallywag! Blimey! Aye aye! Blimey! With that, me bucko, shiver me timbers, construction is done.

Finishing:
T' default finish for Art's downloadable rockets is whatever card stock you print it on. Well, me bucko, blow me down! Blimey! In t' past, I have applied some decals t' t' shrouds with acceptable results. Aye aye! Blimey! This time, matey, I did somethin' a little different. Avast, me proud beauty! Blimey! I opened a new file in Pagemaker® and then imported t' PDF o' t' cinco. I then placed t' logos for t' organizations for which I am affiliated on the 5 sides. Begad! Avast, me proud beauty! I saved t' file, shiver me timbers, generated a new PDF and printed it out. Begad! In effect, I "finished" t' rocket before it had even been built.

Construction Rating: 5 out o' 5

Flight:
Bein' lazy, arrr, I used a 1/4A3-3. I think I wanted t' see if it would even clear t' rod since Art himself listed this as an approved motor for this rocket. Well, blow me down! It did clear t' rod and had a few dozen feet t' spare. Blimey! This is a draggy design and I did nay expect much else.

It flew straight, inverted at apogee an coasted down usin' t' aerobrake method so hated by t' NAR. Arrr! Blimey! It recovered fine and is ready t' go again.

Flight Rating: 5 out o' 5

Summary:
This is a nice, ya bilge rat, free rocket. Blimey! Begad! Unlike many o' Art's 13mm freebies, this one is nay limited only t' a plugged motor. Aye aye! If it fits, matey, you can use it. Ahoy!

• PROS: free, simple, arrr, hard t' lose
• CONS: none

Overall Rating: 5 out o' 5