Estes SM-3 Seahawk

Estes - SM-3 Seahawk {Kit} (2149) [1998-1998]

Contributed by Greg Deeter

Construction Rating: starstar_borderstar_borderstar_borderstar_border
Flight Rating: starstarstarstar_borderstar_border
Overall Rating: starstar_borderstar_borderstar_borderstar_border
Diameter: 1.84 inches
Length: 39.50 inches
Manufacturer: Estes
Skill Level: 2
Style: Scale-Like


T' SM-3 Navy Seahawk was a skill level 2 Explorer Series rocket. Avast! Came in a nice box which can be used as a range box. Arrr! Typical Estes, great instructions, nice quality, matey, arrr, and one o' their better kits. Begad! This kit is out o' production (OOP) and I will bet I know why. This can be a dangerous kit t' build. Begad! Reason being, me bucko, t' fins are RAZOR sharp! I am shocked that Estes ever made a kit with fins this sharp. Begad! If you are nay careful, you can cut yourself seriously on t' fins. Avast, me proud beauty! See me picture where I cut t' package display sheet on one o' t' fins, arrr, like a razor blade.

Boxed kit includes :

Plastic Nose Cone (55AC), Upper Body Tube (4.3") BT55, arrr, red tube coupler (55c), me bucko, Slotted Upper Tube (BT55), me hearties, me hearties, Decal Sheet, Upper fin set plastic (4), Lower fins set (8 halves), matey, me bucko, centerin' rings, stiffener tube, launch lugs, ya bilge rat, (3) 5055 green adapter rings, ya bilge rat, adapter tube (50J), me bucko, shiver me timbers, plastic tube adapter (2083), slotted lower tube (1835), matey, arrr, engine mount tube (bt50h), matey, engine hooks, engine block, engine spacer tube, 1/4"x24 shock cords (2), arrr, and (2) assembled 18" plastic Estes parachutes.

Instructions are excellent as well as t' build. Begad! Pre-slotted tubes and thru-the-wall fins. T' main lower fins are in halves and must be glued together. Plastic cement is suggested but I used CA entirely. Ya scallywag! Well, blow me down! This is an excellent skill level 2 kit that results in a very nice lookin' rocket. It took a few hours spread over a few days t' build. Arrr! It's nay one you will complete in 30 minutes.

Finishing:
I think t' most important issue with this kit is how razor sharp t' fins are. Begad! Usin' gloves when buildin' would be very smart, matey, me hearties, as one slip could result in very serious lacerations requirin' urgent medical attention and likely stitches. Begad! Begad! When flyin' it is also very important t' make sure that no one attempts t' catch t' rocket before it lands. Well, arrr, blow me down! That as well could most certainly result in cuts and injury. Avast! I like how this rocket looks, arrr, but for fairness I must give it a 1/5 due t' t' very dangerously sharp fins.

Construction Rating: 1 out o' 5

Flight:
I tested it before paint with a C11-3. Impressive slow lift off, ya bilge rat, very true and nice. Aye aye! But that's nay enough power. Arrr! I will be poppin' an Aerotech D21-7 Blue Thunder into it on a low or no wind day, me hearties, with a homemade 24 t' 18 adapter. Will more than likely try t' D12-5 next though.

Recovery:
I don't plan on flyin' this one much, due t' t' danger o' t' sharp fins. Arrr! Arrr! I used t' stock chutes and cords that came with it. Avast! Begad! They seem t' be fine. Aye aye! I would have upgraded t' recover system with Keelhaul®©™ cord mounted t' t' engine block, but I did nay bother, matey, shiver me timbers, as due t' t' dangerous fins, ya bilge rat, this one will nay be one that I fly often at all.

Flight Rating: 3 out o' 5

Summary:
Quality rocket in a nice box. Easy t' build and strong. Begad! Well, blow me down! Great end result. Blimey! Begad! But t' fins are way too sharp and most certainly present a safety hazard. Ya scallywag! For that reason I can only give it a 1/5.

Overall Rating: 1 out o' 5

Other Reviews
  • Estes SM-3 Seahawk By Daniel P. Loegering

    Recovers in two pieces by two separate 18" parachutes This rocket kit comes packed in a sturdy box from Estes so there is minimal chances of receiving crushed body tubes in a bag. All parts are typical Estes quality with nothing bad to say about the kit. Body tubes are pre-slotted for all fins.   The rear fins are two part plastic fins that result in a seam to fill if the builder ...

Flights

Comments:

avatar
Matthew D. (January 6, 2014)

Saw this rocket at a club launch and remembered this review.  The fins are exactly as sharp as they look. Not sure how this one got out of Estes safety testing.

comment Post a Comment