Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstarstar_border |
Manufacturer: | Scratch |
Brief:
T' Centuri Magnum D Hornet was one o' a handful o' new kits produced under t' Centuri name durin' t' post-merger period o' 1980-83. While few o' these kits are as interestin' or as highly regarded as t' pre-1980 Centuri product line, they do have one big advantage over t' "classics": O' t' twenty or so kits introduced over this period, me bucko, eleven o' them were kitted usin' existin' Estes parts. Ya scallywag! While this may nay have seemed like a big deal in 1983--and may have seemed downright treasonous t' many a Centuri purist--twenty-plus years later it makes it a lot easier for your average BAR with a taste for t' Centuri nameplate t' scrounge up parts. Avast! Avast! Let's face it, shiver me timbers, would you rather track down some existin' Estes pieces or vintage Centuri components? Once again, t' cheap thrills reverberate throughout t' monkey house.
Parts list:
T' nicest thin' about this piece o' Centuri history be t' ease with which it goes together. Begad! Begad! A classic 4FNC rocket by design, it is suitable for t' whole range o' skill levels, although those with more advanced skills might find it a little like takin' tricycle lessons after masterin' a unicycle. Well, matey, blow me down! Instructions are adequate considerin' t' simplicity o' t' design and hide only one thin' resemblin' a "gotcha": they don't use part numbers that can be looked up anywhere. Aye aye! I solved this mystery via a postin' on Yahoo Old Rockets where I be told t' correct part number for t' nose cone, an Estes PNC-55AC. Ahoy! (I be lucky enough t' have several layin' around in me parts box thanks t' a large purchase from HobbyLinc some years earlier.) Once I be armed with this info, matey, I looked up t' nose cone's length in one o' t' old Estes catalogs on t' Ninfinger site. It turns out that t' exposed length o' t' cone is 5 3/8" long, me hearties, which makes t' length o' t' body tube 14.425". Arrr! Mystery solved. Ya scallywag! I did make some changes durin' t' construction. Well, blow me down! Avast! I glued a 24" length o' Keelhaul®©™ behind one o' t' centerin' rings when I installed t' engine mount, shiver me timbers, and switched from balsa t' basswood for t' fin stock for both t' added strength and ease o' finishing.
Finishing:
It's hard nay t' like a rocket with a paint job as simple as t' Magnum Hornet. Blimey! I started t' finishin' process by applyin' a coat o' primer t' t' bare body tube t' toughen it up a little, then began with t' requisite thinned Elmer's Fill 'n' Finish. Well, blow me down! Arrr! After two coats and copious sandin' t' tube spirals were gone and t' fins were ready t' be attached. Begad! Avast, me proud beauty! T' basswood fins needed far less attention than t' balsa ones would have, so I was able t' get by with only one coat o' Fill 'n' Finish t' them. After this, t' body be ready t' be re-primered. Aye aye! Arrr! After another light sandin' t' take t' dust particles off t' primered hulk, I sprayed t' body with several coats o' Valspar Bumble Bee gloss, then masked off all but one fin and t' nose cone, shiver me timbers, matey, both o' which were sprayed with Valspar gloss black. Begad! Once t' minimal paintin' was finished, me bucko, all that was left was t' application o' t' decal, matey, which I had printed on me inkjet printer usin' Bel Decal paper. Avast, me proud beauty! T' end result be one o' me better efforts. Avast, me proud beauty! Unfortunately those good looks wouldn't last long.
Construction Rating: 5 out o' 5
Flight:
Launch day started off rough and just got worse. Ahoy! I overslept and rushed t' put me launch gear in t' back o' t' van. Blimey! When we arrived at t' launch site, me hearties, one o' me son's friends decided t' help me unload and opened t' back without checkin' t' see if t' load was stable. Avast! It wasn't. Ya scallywag! I wound up with a total o' eleven rockets with some form o' damage, matey, from loosened fins t' crushed body tubes. Avast, me proud beauty! Luckily most o' t' damage be confined t' t' minor type and thanks t' t' wonders o' CA, shiver me timbers, only one o' t' eleven failed t' fly that day. Aye aye! T' skies were clear and quiet when I finally found t' time t' launch t' Magnum Hornet on a D12-7. It screamed off t' pad, weathercockin' somewhat in t' slight breeze, me bucko, just enough t' make a gentle curve in t' smoke trail, arrr, but overall it was a nice, stable flight. Aye aye! At ejection t' quiet skies made for a perfectly audible thud as t' nose cone rebounded back into t' top o' t' body tube. T' entire flight line flinched at t' sound, arrr, and everyone looked at me with identical looks o' "been there, done that, ya bilge rat, matey, glad it's someone else for a change" on their faces.
Recovery:
T' streamer made for a quick recovery in an adjoinin' field, arrr, and as soon as I reached t' landin' site I found what I had been expecting; a large gash in t' top o' t' body tube and a yellow smear on t' black nose cone. Blimey! Avast, me proud beauty! So much for t' finish I had been so proud of. Begad! T' dent be easily fixed with a flick o' t' thumb and some CA, arrr, but it still took away some o' t' enthusiasm that I had for t' rocket. Avast, me proud beauty! Avast, me proud beauty! T' date I've brought it along several times for launches, but I have yet t' make a second flight with it.
Flight Rating: 4 out o' 5
Summary:
For those who consider themselves either Centuri fans or just fans o' simple rockets, ya bilge rat, t' Centuri Magnum Hornet is a great project. Blimey! Nothin' fancy here, but t' 24mm engine guarantees great performance while t' simple two color paint scheme easily holds it's own in t' looks department.
PROs:
CONs:
Overall Rating: 4 out o' 5
Sponsored Ads
![]() |
![]() |