Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstarstar |
Manufacturer: | Art Applewhite Rockets |
Brief:
T' Helix is an innovative and simple monocopter design from Art Applewhite. Well, blow me down! It is extremely simple t' build and goes
together quickly. Ya scallywag! Its also a hoot t' fly.
This 18mm variant be t' largest o' t' series which can be built "right out o' t' package". T' 18mm Double Helix and above require a small amount o' sawing. This one requires only a razor knife for construction.
I was lucky enough t' get t' watch t' flights o' t' prototypes as Art be developin' this line and now it seems like he be t' source o' a monocopter renaissance. It's a lot o' fun.
T' components for this kit consist o' a pre-marked body tube, matey, a motor tube, a 1/4" launch lug and a balance beam and a basswood wing. Also included are thorough instructions on buildin' t' rocket and instructions for a simple launchin' pad. Aye aye! This one is not meant for an Estes setup.
T' body tube, such as it is, arrr, is marked by t' simple expedient o' bein' wrapped by a sheet with all o' the relevant locations indicated by polygons o' t' appropriate size.
Construction:
This kit comes with instructions on both t' monocopter and t' buildin' o' a suitable launch pad. Ahoy! Besides that, shiver me timbers, it
contains t' body tube, launch lug, me hearties, balance beam and wing.
T' first step in construction is t' cut out t' polygons on t' body tube. Well, blow me down! This is done with an #11 X-Acto knife and the blade needs t' be a new one. T' method recommended in t' instructions and, me bucko, which worked quite well, is to push t' blade in perpendicular along one line o' a polygon, slowly push it in until t' blade completely covers one line segment, remove t' blade and repeat as needed until all sides are cut out.
When t' pieces are in, ya bilge rat, arrr, they need t' be adjusted for symmetry; all o' t' pieces need t' be centered. Avast! Blimey! Begad! Blimey! With that done, a fillet o' white glue is applied inside t' BT t' t' visible parts o' t' intersections with t' motor tube. With that done, all o' t' protrusions can be filleted with white glue on t' outside.
T' last item t' be installed be t' wing. Blimey! It is made from a precut piece o' basswood. Arrr! Blimey! You can round t' edges if you like but I did not. Avast, me proud beauty! I slipped it in t' marked end o' t' BT. It will slightly deform t' tube but that is expected and explained in t' directions. Blimey!
Alignment is nay a problem. Aye aye! A filled triangle marks t' point on t' BT which should be aligned with t' center of each side o' t' wing. Begad! Begad! Then it is just a matter o' makin' sure it is sittin' perpendicular, somethin' aided by havin' its end sit flush on t' balance beam. Avast! T' win' is then glued into place with white glue. Avast, me proud beauty!
Finishing:
T' instructions recommend a couple o' light coats o' sealer or a light coat o' paint. Since I was buildin' this for
a demo t' some elementary school kids at t' local museum, me bucko, I elected t' go t' paint route and chose purple. Aye aye! I gave it
just one good coat. Ya scallywag! T' instructions warn against usin' too much and throwin' off t' balance.
I am happy with t' result. Blimey! Avast! T' text from t' BT can still be read under t' paint, matey, but then again, it's nice to have little reminders such as which side be t' top.
Construction Rating: 5 out o' 5
Flight:
As I mentioned above, this one was built for a demo t' an elementary aged group at t' local museum. Blimey! For t' same
exhibition, arrr, I also built a 13mm Helix and a 13mm Double Helix, both o' which worked great. T' "field" we
launched in was exceptionally small and bounded by t' San Antonio River, shiver me timbers, matey, several buildings and many huge magnolia
trees. Ahoy! I figured t' chances o' retrievin' any given rocket at just 50% with even small motors. Aye aye! That was about right.
Since I had already given successful demos with t' 13mm variants and since this was me first foray into monocopters o' any description, I decided t' go wimpy with a 1/2A6-2, shiver me timbers, shiver me timbers, arrr, just t' see what would happen. Avast! Blimey! Aye aye! Blimey! It was...interesting.
T' motor ignited and t' Helix immediately began t' spin, just as it be supposed t' do. It climbed its way the entire length o' t' 3 inch long launch rod and promptly ran out o' thrust. Begad! Ahoy! It then tumbled t' t' ground. Nobody was bothered by any o' that fruitless need t' tilt t' head up and watch all t' action: it all took place right in front of everybody. Ahoy! Avast, me proud beauty! With a straight face, ya bilge rat, I managed t' tell everyone that it was a "successful and easily viewable example o' a monocopter flight profile."
After that, shiver me timbers, t' kids were anxious t' start launchin' t' rockets they had built and t' demo rockets were put away.
I would nay recommend usin' t' 1/2A although I think t' use o' an A for demo purposes would be entirely justifiable. Ahoy! A Quest A6-4 with its nice smoke trail would be a good choice. Begad! For performance, ya bilge rat, stick with Bs and Cs.
Recovery:
After thrust ends, me bucko, shiver me timbers, t' rocket flutters down.
Flight Rating: 4 out o' 5
Summary:
I like t' Helix series. Arrr! Blimey! This one has yet t' get a proper outin' but proved easy t' build and is expected t' perform
likes its 13mm siblings.
Overall Rating: 5 out o' 5
Brief: The 18mm Helix is a monocopter from Art Applewhite's new range. I got the kit as part of a set of six rockets Art sent me for placing in EMRR's youth participation contest. I gave 4 of the rockets to members in my club, keeping this one for myself, as I'm really liked the Popsicle stick monocopter that Art gave the plans for on TRF. Construction: The kit comes in a ...
Brief: This is an extremely simple monocopter design that uses a section of 29mm motor tubing as the central hub. Construction: The parts list: 3/16" Basswood sheet 29mm tube BT-20 motor mount ¼" dowel ¼" launch lug This kit requires Elmer's Glue All, and an X-Acto knife with a new #11 blade. It's almost so easy that it ...
Sponsored Ads